If Safe Mode fails to load, it indicates deep Operating System issues. It would be recommended at this point to take the computer in to your local Micro Center store or look in to a System Recovery to wipe out the system and restore it to the factory settings.
Close this window and proceed. In the bottom left corner of the screen, click on the Start button and then choose All Programs. On the All Programs menu, locate the Accessories folder. Within the Accessories folder, locate the System Tools folder and click System Restore, then wait a few minutes as the program opens. Look at the recommended restore point and determine if the computer was working properly at that time.
If it was, click on Next. On the next screen, verify that the settings are correct and click Finish to start the restore process. Select "System Restore" from the list of search results.
Select the restore point you want to use. Windows will suggest a restore point, which will usually be the most recent one. Check the "Show more restore points" box to see all the available restore points. There may not be many to choose from, as Windows automatically deletes older restore points to save space.
Each restore point will have a short description of what occurred to cause the restore point to be created. Click the. Scan for affected programs button after selecting a restore point. This will show you all of the programs and drivers that will be uninstalled or reinstalled by performing the restore with that restore point. Any programs installed after the restore point was created will be uninstalled, while any programs uninstalled after the restore point was created will be reinstalled.
Review the restore point before restoring. Before proceeding with the system restore, review the changes one last time. Click Finish to begin the restore process. Wait for the restore process to complete. After confirming that you want to restore, the computer will reboot and the restore process will begin.
This will likely take a few minutes. Confirm that the restore was successful. Once the restore is complete, Windows will boot and a message will appear indicating that the restore was successful.
Test your computer to see if the restore fixed your problem. If it didn't you can try restoring to an earlier restore point. Ensure that System Restore is enabled. In order to use System Restore, it must be enabled for your computer. If System Restore isn't starting, check to make sure that it's turned on. Click the Start menu, right-click on Computer, and select "Properties". Click the "System protection" link, and then select the drive you are trying to run System Restore on.
Click Configure You can run the System Restore tool from the Command Prompt if something has gone wrong and you can't start Windows normally. Reboot your computer and hold the F8 key. This will open the Advanced Boot Options menu. Windows will load essential files and then take you to the Command Prompt. Type rstrui. This will start the System Restore utility. Follow the instructions in the section above to restore your computer.
When performing a system restore from Safe Mode, you won't be able to undo it. Run the Check Disk utility to check for problems with the hard drive. A failing hard drive could be causing System Restore to malfunction. Check Disk can potentially repair these issues. Click Start, right-click on Command Prompt, and select "Run as administrator". Confirm that you want to reboot your computer.
Check Disk will run before Windows starts and scan for errors. It will attempt to fix any errors that it finds. Perform virus and malware scans. Viruses may infect your restore points, or disable System Restore from starting. Removing these viruses will be the only way to get System Restore working again, short of reinstalling Windows completely.
Click here for detailed instructions on removing viruses. Consider reinstalling Windows if the System Restore doesn't work. If all else fails, reinstalling Windows may be the only way to fix your problems.
If you have your important files backed up already, the reinstallation process will likely go faster than you think, and will typically improve your computer's performance. Click here for detail instructions on reinstalling Windows 7. Method 2. Click the Start menu, right-click "Computer", and then click "Properties". You can manually create System Restore points, which is very useful if you have your system working well and want to have a reference point you can revert back to in case things go wrong.
Please note that system restore does not affect your documents, pictures, or other personal data, so please feel free to restore your computer when something goes wrong. We cannot predict the unexpected things, but we can prevent it by creating a system restore point. With it, you can undo the harmful change via System Restore. But if you cannot boot your computer? System restore in safe mode may be a great idea.
It helps when you cannot boot the Windows. Also, it works when your computer is infected by malware, or the system keep crashing or blue-screening owing to updated drivers. To restore computer in safe mode, you need to ensure that there is an available restore point.
It's the premise to restore computer in safe mode. But some users report that they can't boot into safe mode in Windows 7. You could consider jump to the last part. Step 1. Start your computer, and press the F8 key repeatedly before showing the Windows logo. Then, you will see the Advanced Boot Options.
Step 2. Then, choose your account to log in when the safe mode loads and click X to close the pop-up box What Is Safe Mode. Step 3. Or you can directly type System Restore in the search box, then select it. Step 4. In this window, you need to make sure if the recommended system restore point is working properly at that time. If yes, click Next. If not, tick Choose a different restore point.
0コメント